Modal Based Sensitivity Analysis of Crack in Turbine Blades Using Validated Finite Element Models
(*) Corresponding author
Turbines in power industry use pretwisted blades of varying lengths, which are mounted on the rotating shafts with one end fitted in the fir tree root of the rotor. The fatigue of these blades may cause crack that starts at the stress concentration regions and may propagate for catastrophic failure. This paper addresses the vibration behavior of the pretwisted blades under the influence of crack. The effect of crack on the natural frequencies of pretwisted blade is investigated by conducting parametric studies using finite element analysis software. The results obtained are used to evaluate the influence of crack on turbine blade after validating with experimental results. It has been observed that the crack in a blade had a considerable effect on the natural frequencies that change with varying pretwist angles in all the modes of vibration. In addition, the crack sensitivity for natural frequencies of long and short blades has been compared and the fatigue behavior of these blades has been analysed.
Copyright © 2019 Praise Worthy Prize - All rights reserved.
H. H. Yoo, J. H. Park, and J. Park, Vibration Analysis of Rotating Pre-twisted Blades, Computers and Structures, Vol. 79, n. 19, 1811-1819, 2001.
J. Chung, and H. H. Yoo, Dynamic Analysis of a Rotating Cantilever Beam by using the Finite Element Method, Journal of Sound and Vibration, Vol. 249, n. 1, 147-164, 2002.
H. H. Yoo, and C. Pierre, Modal Characteristics of a Rotating Rectangular Cantilever Plate, Journal of Sound and Vibration, Vol. 259, n. 1, 81-96, 2003.
B. W. Huang, Effect of Number of Blades and Distribution of Cracks on Vibration Localization in a Cracked Pre-Twisted Blade System, International Journal of Mechanical Sciences, Vol. 48, n. 1, 1-10, 2006.
D. N. Vadiraja, and A. D. Sahasrabudhe, Vibration Analysis and Optimal Control of Rotating Pre-twisted Thin-walled Beams using MFC Actuators and Sensors, Thin-Walled Structures, Vol. 47, n. 5, 555-567, 2009.
W. R. Chen, On the Vibration and Stability of Spinning Axially Loaded Pre-twisted Timoshenko Beams, Finite Elements in Analysis and Design, Vol. 46, n. 11, 1037-1047, 2010.
S. K. Sinha, and K. E. Turner, Natural Frequencies of a Pre-twisted Blade in a Centrifugal Force Field, Journal of Sound and Vibration, Vol. 330, n. 11, 2655-2681, 2011.
Y. Cheng, Z. Yu, and Y. Yuan, Vibration Analysis of a Cracked Rotating Tapered Beam using the p-version Finite Element Method, Finite Elements in Analysis and Design, Vol. 47, n. 7, 825-834, 2011.
K. V. Nguyen, Mode Shapes Analysis of a Cracked Beam and its Application for Crack Detection, Journal of Sound and Vibration, Vol. 333, n. 3, 848-872, 2014.
S. Akash, and S. P. Harsha, Vibration response Analysis of Last stage LP turbine blades for variable size of crack in root, 3rd International Conference on Innovations in Automation and Mechatronics Engineering, ICIAME 2016, Procedia Technology, 23, 232 – 239, 2016.
M. M. Rezaei, M. Behzad, H. Moradi, and H. Haddadpour, Modal-based damage identification for the nonlinear model of modern wind turbine blade, Renewable Energy, Vol. 94, 391-409, 2016.
J. A.Segura, L. Castro, I. Rosales, J. A. Rodriguez, G. Urquiza, and J. M. Rodriguez, Diagnostic and failure analysis in blades of a 300 MW steam turbine, Engineering Failure Analysis, Vol. 82, 631–641, 2017.
W. Zhao, Y. Li, M. Xue, P. Wang, and J. Jiang, Vibration analysis for failure detection in low pressure steam turbine blades in nuclear power plant, Engineering Failure Analysis, Vol. 84, 11–24, 2018.
Soegihardjo, O., Suhardjono, S., Pramujati, B., Pramono, A., Parametric Beam Modeling to Predict the First Natural Bending Frequency of Thin Wall Box-Shaped Structures Verified Using Experimental Modal Analysis, (2017) International Review of Mechanical Engineering (IREME), 11 (1), pp. 77-86.
Karanjkar, A., Banerjee, N., Experimental and Finite Element Investigation of Free Vibration Behaviour of Car Bonnet, (2017) International Review of Mechanical Engineering (IREME), 11 (7), pp. 448-453.
S.B. Salunkhe, C.V.Singh, and P.J. Guruprasad, Effect of matrix cracks and delamination on extension-twist coupling of thin pretwisted composite strips, Composite Structures, Vol. 180, 234-250, 2017.
Y. Oh, and H.H. Yoo, Vibration analysis of a rotating pre-twisted blade considering the coupling effects of stretching, bending, and torsion, Journal of Sound and Vibration, Vol. 431, 20-39, 2018.
Sedelnikov, A., Molyavko, D., Potienko, K., Study of Over-assessment of Microaccelerations when Using a Beam-Model of Elastic Elements, (2016) International Review of Aerospace Engineering (IREASE), 9 (1), pp. 7-12.
Ecsedi, I., Lengyel, Á., Analysis of Layered Composite Beam with Imperfect Shear Connection by Means of Energy Method, (2018) International Journal on Engineering Applications (IREA), 6 (2), pp. 42-51.
Bakhti, M., Idrissi, B., Highly Nonlinear Flexible Manipulator State Estimation Using the Extended and the Unscented Kalman Filters, (2016) International Review of Automatic Control (IREACO), 9 (3), pp. 151-160.
Lahssan, B., Bakhti, M., Bououlid Idrissi, B., Flexible Manipulator State Reconstruction Using Luenberger and First Order Sliding Mode Observers Under Parametric Uncertainties, (2016) International Review on Modelling and Simulations (IREMOS), 9 (6), pp. 427-434.
- There are currently no refbacks.
Please send any question about this web site to email@example.com
Copyright © 2005-2023 Praise Worthy Prize