Open Access Open Access  Restricted Access Subscription or Fee Access

Design and Comparison of High-Speed Induction Machine and High-Speed Interior Permanent Magnet Machine


(*) Corresponding author


Authors' affiliations


DOI: https://doi.org/10.15866/iremos.v11i3.14112

Abstract


Designing high-speed machines is a complicated process that needs thorough investigation due to their various applications in the industry. The choice of selecting between Induction Machines (IMs) and Permanent magnet Machines (PMs) depends on the required robustness, efficiency, and cost. In this paper, an IM and Interior Permanent magnet Machine (IPM) with similar output power (10kW), rotational speed (30,000rpm), and input voltage (380V) with Fractional-Slot Concentrated Winding (FSCW) are designed, optimized, and analyzed. The comparison is based on design challenges, cost, and efficiency. A genetic Algorithm is used to optimize the proposed machines and finite element analysis (Maxwell) is employed to support the result.
Copyright © 2018 Praise Worthy Prize - All rights reserved.

Keywords


High-Speed Machines; Machine Design; Induction Machine; Interior Permanent Magnet Machine

Full Text:

PDF


References


O. Bottesi and L. Alberti, “Comparison of small-size generator for high-efficiency hydroelectric energy production,” in 2017 IEEE International Electric Machines and Drives Conference (IEMDC), 2017, pp. 1–8.
http://dx.doi.org/10.1109/iemdc.2017.8002062

S. Li, Y. Li, W. Choi, and B. Sarlioglu, “High-Speed Electric Machines: Challenges and Design Considerations,” IEEE Trans. Transp. Electrif., vol. 2, no. 1, pp. 2–13, Mar. 2016.
http://dx.doi.org/10.1109/tte.2016.2523879

W. L. Soong, G. B. Kliman, R. N. Johnson, R. A. White, and J. E. Miller, “Novel High-Speed Induction Motor for a Commercial Centrifugal Compressor,” IEEE Trans. Ind. Appl., vol. 36, no. 3, pp. 706–713, 2000.
http://dx.doi.org/10.1109/28.845043

T. A. Lipo, Introduction to AC Machine Design, Third. Madison, USA: Wisconsin Power Electronics Research Center, University of Wisconsin, 2011.

H. Dehnavifard, M. A. Khan, and P. S. Barendse, “Development of a 5-kW Scaled Prototype of a 2.5 MW Doubly-Fed Induction Generator,” IEEE Trans. Ind. Appl., vol. 52, no. 6, pp. 4688–4698, Nov. 2016.
http://dx.doi.org/10.1109/tia.2016.2591512

J. N. Stander, G. Venter, and M. J. Kamper, “Review of Direct-Drive Radial Flux Wind Turbine Generator Mechanical Design,” Wind Energ., vol. 15, no. 3, pp. 459–472, 2011.
http://dx.doi.org/10.1002/we.484

B. M. Wilamowski and J. D. Irwin, Power Electronics and Motor Drives. CRC Press, 2011.

R. D. van Millingen and J. D. V. M. R. D. Van Millingen, C. Eng, “Phase Shift Torquemeters for Gas Turbine Development and Monitoring,” in International Gas Turbine and Aeroengine Congress and Exposition, 1991, pp. 1–10.
http://dx.doi.org/10.1115/91-gt-189

Z. Kolondzovski, “Thermal and Mechanical Analysis of High-Speed Permanent-Magnet Electrical Machines,” Aalto University, 2010.

A. Borisavljevic, Limits, Modeling and Design of High-Speed Permanent Magnet Machines. Berlin, Heidelberg: Springer Berlin Heidelberg, 2013.

M. A. Rahman, A. Chiba, and T. Fukao, “Super high speed electrical machines - summary,” in IEEE Power Engineering Society General Meeting, 2004., vol. 2, pp. 1272–1275.
http://dx.doi.org/10.1109/pes.2004.1373062

R. R. Moghaddam, “High speed operation of electrical machines, a review on technology, benefits and challenges,” in 2014 IEEE Energy Conversion Congress and Exposition (ECCE), 2014, pp. 5539–5546.
http://dx.doi.org/10.1109/ecce.2014.6954160

M. Centner and U. Schafer, “Optimized Design of High-Speed Induction Motors in Respect of the Electrical Steel Grade,” IEEE Trans. Ind. Electron., vol. 57, no. 1, pp. 288–295, 2010.
http://dx.doi.org/10.1109/tie.2009.2029523

A. J. Mitcham and N. Grum, “An Integrated LP Shaft Generator for the more Electric Aircraft,” in IEE Coloquium on All Electric Aircraft, 1998, p. 8/1--8/9.
http://dx.doi.org/10.1049/ic:19980346

D. Gerada, A. Mebarki, N. L. Brown, C. Gerada, A. Cavagnino, and A. Boglietti, “High-Speed Electrical Machines: Technologies, Trends, and Developments,” IEEE Trans. Ind. Electron., vol. 61, no. 6, pp. 2946–2959, Jun. 2014.
http://dx.doi.org/10.1109/tie.2013.2286777

J. Gieras, Permanent Magnet Motor Technology, vol. 20096073. CRC Press, 2009.
http://dx.doi.org/10.1201/9781420064414

E. Carraro, M. Degano, M. Morandin, and N. Bianchi, “PM synchronous machine comparison for light electric vehicles,” in 2014 IEEE International Electric Vehicle Conference (IEVC), 2014, pp. 1–8.
http://dx.doi.org/10.1109/ievc.2014.7056200

M. Vetuschi et al., “Limits, Modeling and Design of High-Speed Permanent Magnet Machines,” Proc. - 2014 Int. Conf. Electr. Mach. ICEM 2014, vol. 3, no. 1, pp. 150–155, Sep. 2014.
http://dx.doi.org/10.1109/icelmach.2014.6960325

P. B. Reddy, A. M. El-Refaie, K.-K. Huh, J. K. Tangudu, and T. M. Jahns, “Comparison of Interior and Surface PM Machines Equipped With Fractional-Slot Concentrated Windings for Hybrid Traction Applications,” IEEE Trans. Energy Convers., vol. 27, no. 3, pp. 593–602, Sep. 2012.
http://dx.doi.org/10.1109/tec.2012.2195316

J. Singh, “Harmonic Analysis and Loss Comparison of Microcomputer-Based PWM Strategies for Induction Motor Drive,” Electr. Mach. Power Syst., vol. 27, no. 10, pp. 1129–1139, 1999.
http://dx.doi.org/10.1080/073135699268768

W. L. Soong, P. B. Reddy, A. M. El-Refaie, T. M. Jahns, and N. Ertugrul, “Surface PM Machine Parameter Selection for Wide Field-Weakening Applications,” in 2007 IEEE Industry Applications Annual Meeting, 2007, pp. 882–889.
http://dx.doi.org/10.1109/07ias.2007.138

K. Ohyama, M. N. F. Nashed, K. Aso, H. Fujii, and H. Uehara, “Design using Finite Element Analysis of Switched Reluctance Motor for Electric Vehicle,” in 2006 2nd International Conference on Information & Communication Technologies, vol. 1, pp. 727–732.
http://dx.doi.org/10.1109/ictta.2006.1684462

H. Dehnavifard, “Development of a Scaled Doubly-Fed Induction Generator for Assessment of Wind Power Integration Issues,” University of Cape Town, 2016.

J. R. Hendershot and T. J. E. Miller, Design of Brushless Permanent- Magnet Motors. Ohio: Magna Physics, 1994.

I. Boldea and S. A. Nasar, The Induction Machines Design Handbook. CRC Press/Taylor & Francis, 2010.
http://dx.doi.org/10.1201/9781420066692

S. Huang, J. Luo, S. Member, F. Leonardi, and A. Member, “A General Approach to Sizing and Power Density Equations for Comparison of Electrical Machines,”IEEE Transactions on Industry Applications, vol. 34, no. 1, pp. 92–97, 1998.
http://dx.doi.org/10.1109/28.658727

J. R. Hendershot, “MotorSolve analysis of the 2010 Toyota Prius Traction Motor,” 2015, pp. 1–64.

A. M. EL-Refaie, M. R. Shah, J. P. Alexander, S. Galioto, K.-K. Huh, and W. D. Gerstler, “Rotor End Losses in Multiphase Fractional-Slot Concentrated-Winding Permanent Magnet Synchronous Machines,” IEEE Trans. Ind. Appl., vol. 47, no. 5, pp. 2066–2074, Sep. 2011.
http://dx.doi.org/10.1109/tia.2011.2162049

Ismagilov, F., Vavilov, V., Bekuzin, V., Ayguzina, V., Topology Evaluation of a Slotless High-Speed Electrical Machine with Stator Core Made of an Amorphous Alloy for the Aerospace Industry, (2017) International Review of Aerospace Engineering (IREASE), 10 (3), pp. 131-139.
http://dx.doi.org/10.15866/irease.v10i3.12615

Barta, J., Uzhegov, N., Ondrusek, C., Pyrhönen, J., High-Speed Electrical Machine Topology Selection for the 6kW, 120 000 rpm Helium Turbo-Circulator, (2016) International Review of Electrical Engineering (IREE), 11 (1), pp. 36-44.
http://dx.doi.org/10.15866/iree.v11i1.7687

Ismagilov, F., Uzhegov, N., Vavilov, V., Gusakov, D., Design Aspects of a High-Speed High-Voltage PMSM for Aerospace Application, (2017) International Review of Aerospace Engineering (IREASE), 10 (3), pp. 122-130.
http://dx.doi.org/10.15866/irease.v10i3.12487


Refbacks

  • There are currently no refbacks.



Please send any question about this web site to info@praiseworthyprize.com
Copyright © 2005-2024 Praise Worthy Prize