| Issue | Title | |
| Vol 12, No 2 (2018) | 2D Hydrodynamic Blade Analysis of Tidal Darrieus Turbine | Abstract |
| Charalampos D. Maritsis, Eleni Douvi, Dionissios Margaris | ||
| Vol 8, No 1 (2014) | 2D Simulation of FC72 Sessile Droplet Evaporation in the Constant Contact Line Region | Abstract |
| S. Hussain, Y. Fukatani, M. Kohno, K. Sefiane, Y. Takata | ||
| Vol 9, No 4 (2015) | A Bipotential Method Coupling Contact, Friction and Adhesion | Abstract |
| Nazihe Terfaya, A. Berga, M. Raous | ||
| Vol 8, No 3 (2014) | A CFD Investigation of Different Port Runner in a GDI Engine | Abstract |
| P. Ramesh, E. James Gunasekaran | ||
| Vol 8, No 5 (2014) | A Comparative Performance Analysis of Gas Lubricated Cylindrical and Elliptical Journal Bearings | Abstract |
| Marco Tulio C. Faria | ||
| Vol 14, No 4 (2020) | A Comparative Study of Seismic and Tsunami Vulnerability of Structures Located in the Coastal Area of Rabat-Salé, Morocco | Abstract |
| E. Nchiti, A. El Hammoumi, Kamal Gueraoui, A. Iben Brahim | ||
| Vol 11, No 10 (2017) | A Comparative Study of the Enhancement of Heat Transfer by Delta Wing Vortex Generators and V Shaped Dimples Using Experimentation and CFD | Abstract |
| A. A. Satam, V. N. Raibhole | ||
| Vol 7, No 6 (2013) | A Comparative Study of Two Mechanical Agitated System in Case of Non-Newtonian Fluids | Abstract |
| L. Rahmani, B. Draoui, E. Benachour, B. Mebarki, Oussama Seghier | ||
| Vol 7, No 4 (2013) | A Comparative Study on Predicting Methods for Cell Formation Problem | Abstract |
| Sanaa Ali Hamza, Erry Yulian T. Adesta | ||
| Vol 7, No 6 (2013) | A Comparison of Cylindrical and Row Trenched Cooling Holes with Alignment Angle of 90 Degree Near the Combustor Endwall | Abstract |
| Ehsan Kianpour, Nor Azwadi C. Sidik, Syahrullail Samion | ||
| Vol 17, No 4 (2023) | A Comparison of Performance Simulation Between PID and Fuzzy Logic Controller for an Autonomous Trajectory of a Floater Glider | Abstract |
| Nanang Joko Hadi Purnomo, Agus Ahmad Masroeri, Wibowo Harso Nugroho, Endah Suwarni | ||
| Vol 7, No 7 (2013) | A Comprehensive CFD Model of Protonexchange Membrane Fuel Cell | Abstract |
| F. Tiss, T. Ghabara, R. Chouikh, A. Guizani | ||
| Vol 9, No 1 (2015) | A Comprehensive Review on the Application of Evolutionary Computation in Design Optimization of Plate-Fin Heat Exchangers | Abstract |
| Moslem Yousefi, Milad Yousefi, Weria Khaksar, Firas B. Ismail Alnaimi, Amer Nordin Darus | ||
| Vol 8, No 2 (2014) | A Computational Analysis of Flow Structure Through a Constant Area DS-Duct | Abstract |
| A. K. Biswas, Prasanta K. Sinha, A. N. Mullick, B. Majumdar | ||
| Vol 16, No 2 (2022) | A Computer Code for Wave Propagation in Flexible Pipelines Under Fluid Hammer Conditions | Abstract |
| Dimitrios G. Pavlou | ||
| Vol 13, No 12 (2019) | A Design Process to Parameterize a Real-Time Simulation Model of a Commercial Vehicle | Abstract |
| Manouchehr Mohammadi, Emil Kurvinen, Aki Mikkola | ||
| Vol 11, No 4 (2017) | A Fault Diagnosis Expert System for Building Chillers | Abstract |
| C. N. Tan, C. F. Tan, M. A. Abdullah | ||
| Vol 7, No 3 (2013) | A Full Scale Motorcycle Dynamic Rig | Abstract |
| D. De Falco, G. Di Massa, S. Pagano | ||
| Vol 7, No 5 (2013) | A Full Scale Test Rig to Characterize Pneumatic Tyre Mechanical Behaviour | Abstract |
| Flavio Farroni, Ernesto Rocca, Francesco Timpone | ||
| Vol 12, No 8 (2018) | A Geometric Algorithm for Redundant Inverse Kinematics with Obstacle Avoidance in a Known Environment | Abstract |
| Kun Wang, Qi Wang, Huapeng Wu, Kun Jiang | ||
| Vol 8, No 6 (2014) | A Knowledge-Based Industrial Robot Selection System for Manufacturing Industries | Abstract |
| CheeFai Tan, S. N. Khalil, N. Tamaldin, J. Karjanto, M. Y. Nidzamuddin, L. S. Wahidin, W. Chen, G. W. M. Rauterberg | ||
| Vol 15, No 11 (2021) | A Mating Technique for Various Crossover in Genetic Algorithm for Optimum System Identification | Abstract |
| Farah Ayiesya Zainuddin, Md Fahmi Abd Samad | ||
| Vol 7, No 6 (2013) | A Microstructure-Based Model for Describing Softening Process During Compression of Al-30%wt Zn Alloy | Abstract |
| M. Borodachenkova, S. Santos, F. Barlat, J. J. Gracio | ||
| Vol 7, No 1 (2013) | A Mild Steel Shear Zone Temperature Minimization Using Genetic Algorithm and Direct Search Toolbox in CNC Turning Operation | Abstract |
| Adnan Abbas, Mohamad Minhat, Md. Nizam | ||
| Vol 15, No 4 (2021) | A Modelling of Cyclic Thermal and Impact Loads on Excavator Bucket | Abstract |
| Kirill Valerievich Gogolinskiy, Dmitrii Sergeevich Gromyka, Eldar Abdollovich Kremcheev | ||
| 1 - 25 of 1120 Items | 1 2 3 4 5 6 7 8 9 10 > >> | |
Please send any question about this web site to info@praiseworthyprize.com
Copyright © 2005-2023 Praise Worthy Prize