Open Access
Subscription or Fee Access
Full Issue
View or download the full issue | FULL PDF |
Table of Contents
Articles
Analysis of Bifurcations, Rattle and Chaos in a Gear Transmission System | |
R. Brancati, U. Montanaro, E. Rocca, S. Santini, F. Timpone | 583-591 |
Effect of Diffuser Angle on the Reattachment Point of an Incompressible Airflow | |
Lincoln Nascimento Ribeiro, Claudia Regina de Andrade, Edson Luiz Zaparoli | 592-598 |
Cams with High Efficiency | |
F. I. Petrescu, R. V. Petrescu | 599-606 |
Dimensionless Analysis and Optimization of Piezoelectric Vibration Energy Harvester | |
Xu Wang, Han Xiao | 607-624 |
Low Reynolds Number Investigation of the Flow Over a NACA 0012 Airfoil at Different Rainfall Rates | |
Eleni C. Douvi, Dionissios P. Margaris, Sotirios D. Lazaropoulos, Stylianos G. Svanas | 625-632 |
The Flight Performance Criteria for Adaptive Control Design During Hydro Planing and Ground Effect Altitude of Wing In Surface Effect-Craft | |
Sayuti Syamsuar, E. B. Djatmiko, P. A. Wilson, - Erwandi, - Subchan | 633-645 |
Simulation Analysis on Thermo Physical Properties of Hydrocarbon Refrigerants in Vapour Compression Refrigeration System | |
P. Thangavel, P. Somasundaram, P. Navaneethakrishnan | 646-651 |
Numerical Investigation on Combustion Behaviors of Direct-Injection Spark Ignition Engine Fueled with CNG-Hydrogen Blends | |
Naima Khatir, Abdelkrim Liazid | 652-663 |
Condensation Heat Transfer Characteristics of R22, R134a, R410A and R407C on Single Horizontal Plain and Finned Tubes | |
Talaat A. Ibrahim, Mohamed A. M. Hassan | 664-672 |
Effects of Incomplete Transesterification Reaction of Palm Oil Biodiesel on Fuel Quality and Engine Performance | |
Watit Pakdee, Cattaleeya Pattamaprom, Sirichai Phanumnuay | 673-678 |
New Algorithm to Avoid Link-Collision in Manipulators with Continuously Changed Hard Limits | |
Moustafa A. Fouz, Amgad M. Bayoumy Aly, Sohair F. Rezeka | 679-685 |
Heat Transfer Enhancement Performance of Al2O3/Water Nanofluid in Condensing Unit of Air Conditioner: Experimental Study | |
V. Chandraprabu, G. Sankaranarayanan, S. Iniyan, S. Suresh, V. Siva | 686-691 |
Similarity Solutions of Marangoni Heat Transfer Flow of Water Based Nanofluid Containing Nanoparticles with Variable Viscosity and Thermal Conductivity | |
M. Ferdows, Shamima Islam, Raushan Ara Quadir | 692-697 |
Diesel Fuel Additives: an Overview | |
S. Ravi, R. Subramanian | 698-704 |
Comparative Studies on Vegetable Oil Usage in C.I Engines as an Alternative to Diesel Fuel | |
L. Karikalan, M. Chandrasekaran, K. Sudhagar | 705-715 |
Performance Study of WEDMed on Inconel 718 by Using Response Surface Methodology | |
M. A. Fairuz,, M. R. M. Hafiezal, R. Hussin, S. A. Adam, A. F. Aiman | 716-720 |
Application of Continuous Improvement in Furniture Manufacturing Industry | |
M. S. Hussin, M. F. M. A. Hamzas, Z. A. Zailani, A. B. Sanuddin | 721-726 |
Investigation of Optimal Parameters for Tensile Strength Property of ABS in Rapid Prototyping | |
M. S. Bahari, A. B. Sanuddin, I. K. Marlina | 727-733 |
Computational Analysis of Flow Structure in a Curved Subsonic Diffusing Duct | |
Prasanta K. Sinha, A. K. Biswas, B. Majumdar | 734-739 |
Design Improvement of ‘Air Remover Fan’ to Reduce Temperature Inside the Car | |
M. S. Hussin, A. B. Sanuddin, Z. A. Zailani, M. F. M. A. Hamzas | 740-744 |
Investigation of Core Thickness Undersized on Composite Panels | |
M. S. Hussin, Z. A. Zailani, M. F. M. A. Hamzas, A. B. Sanuddin | 745-749 |
A Comparative Study on Predicting Methods for Cell Formation Problem | |
Sanaa Ali Hamza, Erry Yulian T. Adesta | 750-756 |
Analysis of Hammer Head at Increased Flow Demand in Pipe Networks: a Case Study | |
Subhasish Das, Biprodip Mukherjee, Asis Mazumdar | 757-766 |
Intelligent Sampling for Inspecting Milled Flat Plates | |
Suleiman M. Obeidat, Wisam M. Abu Jadayil, Nabeel F. Mandahawi | 767-773 |
Sound Quality Evaluation of Vehicle Interior Noise Based on Psychoacoustical Indices | |
J. Ju, Y. S. Wang, Y. F. Xing, G. Q. Shen, H. Guo | 774-782 |
Erratum
Optimization of the Plastic Injection Molding Parameters for Sport Equipment by Using Design of Experiment | |
R. Hussin, R. Mohd Saad, R. Hussin, M. R. M. Hafiezal, M. A. Fairuz | 783 |
Please send any question about this web site to info@praiseworthyprize.com
Copyright © 2005-2024 Praise Worthy Prize