Design and Practical Realization of CNC Device Designed for Automation of the Application of Viscous Materials

Peter Drgona; Rastislav Stefun; Lubos Stefke

doi:10.15866/ireme.v12i8.15153

Design and Practical Realization of CNC Device Designed for Automation of the Application of Viscous Materials

Peter Drgona⁽¹⁾, Rastislav Stefun^(2*), Lubos Stefke⁽³⁾

^(*) Corresponding author

Authors' affiliations

DOI: https://doi.org/10.15866/ireme.v12i8.15153

Abstract

This article deals with the design and the practical realization of a CNC device designed for the application of viscous materials, such as a thermal conducting paste, using standard tubes. The aim of the paper is to give to the reader detailed information about the design process of the CNC machine. In general, thermal conducting paste is used for a better heat dissipation but its application from standard tubes on surface can be an issue. A designed CNC device serves for an easier and a more accurate paste application in production process. Authors tried to design the cheapest possible device. Sufficient mechanical construction has been chosen where designed paste extrusion module has been attached. For selected stepper motors authors designed drivers and, as a base for CNC control an open source firmware has been used, which has been changed according to specific needs. As a result, a functional device has been made, for dispensing uses worm gear instead of being commonly used for air pressure.
Copyright © 2018 Praise Worthy Prize - All rights reserved.

Keywords

CNC Design; CNC Control; Ball Screw; Stepper Motor

Full Text:

PDF

References

R. G. Lins, B. Guerreiro, R. Schmitt, J. Sun, M. Corazzim and F. R. Silva, A novel methodology for retrofitting CNC machines based on the context of industry 4.0, 2017 IEEE International Systems Engineering Symposium (ISSE), Vienna, 2017, pp. 1-6.
http://dx.doi.org/10.1109/syseng.2017.8088293

Koscelnik, J., Frivaldsky, M., Prazenica, M., Mazgut, R., A Review of Multi-elements Resonant Converters Topologies, In: 10th International Conference ELEKTRO 2014, Rajecke Teplice, Slovakia, 19-20 May, 2014, IEEE, pp. 312-317, Catalog number: CFP1448S-CDR.
http://dx.doi.org/10.1109/elektro.2014.6848909

Bhajana, V. V. Subrahmanya Kumar; Drabek, Pavel, A Novel ZCS Non-Isolated Bidirectional Buck-Boost DC-DC Converter for Energy Storage Applications, In: 24th IEEE International Symposium on Industrial Electronics (ISIE), pp. 1224-1229 Published: 2015.
http://dx.doi.org/10.1109/isie.2015.7281647

Stefanec, P., Paskala, M., Dobrucky, B., et al., Control System for Preheating of Molds with using PLC, International Conference on Industrial Technology and Management Science (ITMS 2015), Book Series: ACSR-Advances in Comptuer Science Research, Vol. 34, pp. 1647-1652.
http://dx.doi.org/10.2991/itms-15.2015.401

Duchon, F., Hubinsky, P., Hanzel, J., et al., Intelligent vehicles as the robotic applications, 5th International Conference on Modelling of Mechanical and Mechatronics Systems (MMaMS) 2012-Modelling Of Mechanical And Mechatronics Systems, Book Series: Procedia Engineering Volume: 48 Pages: 105-114.
http://dx.doi.org/10.1016/j.proeng.2012.09.492

http://www.cnc1.eu/sk/KompasH1000GSKIT.htm [cited 11. march 2017].

Kyslan, Karol; Kusnir, Emil; Fedak, Viliam; et al., Dynamic Emulation of Mechanical Loads with Backlash Based on Rapid Control Prototyping, In: 16th International Power Electronics and Motion Control Conference and Exposition (PEMC), Pages 1209-1215, 2014.
http://dx.doi.org/10.1109/epepemc.2014.6980676

http://www.thomsonlinear.com/downloads/screws/Leadscrews_Ballscrews_Splines_cten.pdf [cited 14. april 2017].

Urica, T., Simonova, A., Kascak S., Control design and simulation of continuous systems, Electric power engineering EPE 2017 18th international scientific conference, IEEE, 2017. - ISBN 978-1-5090-6405-2. - USB kľúč, s. 125-129.
http://dx.doi.org/10.1109/epe.2017.7967263

K. Verma and R. M. Belokar, Experimental investigations of ball screws over static and accelerating torque-based lead factor in CNC machining centre, The Journal of Engineering, vol. 2018, no. 1, pp. 17-21, 1 2018.
http://dx.doi.org/10.1049/joe.2017.0298

Fedak, V., Durovsky, F., Uveges, R., et al., HIL Simulator of Drives of an Industrial Robot with 6 DOF, Elektronika Ir Elektrotechnika Vol. 21 Issue 2 Pages 14-19, 2015.
http://dx.doi.org/10.5755/j01.eee.21.2.11506

http://www.linearmotiontips.com/calculate-motor-drive-torque-ball-screws/ [cited 10. may 2017].

http://microcon.cz/ [cited 10. may 2017].

Tereň, A., Špánik, P., Feňo, I., DC/DC converters with soft (ZVS) switching, ELEKTRO 2001: section: electrical engineering.- Žilina: University of Žilina. - ISBN 80-7100-836-2. - S. 82-87.

Simonová, A., Hargaš, L., Koniar, D., Loncová, Z., Hrianka, M., Mathematical analysis of complete operation cycle of a system with two-position controller, ELEKTRO 2016 - 11th international conference IEEE, 2016. - ISBN 978-1-4673-8698-2. - CD-ROM, s. 213-215.
http://dx.doi.org/10.1109/elektro.2016.7512067

Simonová, Anna, Hargaš, Libor, Koniar, Dušan, Hrianka, Miroslav, Loncová, Zuzana, Uriča, Tomáš, Taraba, Michal, Uses of on-off controller for regulation of higher order system in comparator mode, Electrical Engineering-Archiv für Elektrotechnik, SI, SPRINGER, Vol. 99, Issue 4, pp. 1367-1375,
http://dx.doi.org/10.1007/s00202-017-0610-7

TOSHIBA, DATASHEET TB6600, www.toshiba.com

J. M. Berbesi, K. Saumeth and F. Pinilla, Parallel control firmware for CNC milling machine based in Arduino, 12th International Microsystems, Packaging, Assembly and Circuits Technology Conference (IMPACT), Taipei, 2017, pp. 319-322.
http://dx.doi.org/10.1109/impact.2017.8255919

Hock, O., Drgona, P., Paskala, M., Simulation Model of Adjustable Arm Using Denavit-Hartenberg Parameters, ELEKTRO 10th International Conference, 2014, pp176-179.
http://dx.doi.org/10.1109/elektro.2014.6847896

Hock, Ondrej; Drgona, Peter; Frivaldsky, Michal; et al.: Simulation of manipulator positioning methodology using inverse kinematics, In 16th International Scientific Conference on Electric Power Engineering (EPE 2015),pp. 706-711.
http://dx.doi.org/10.1109/epe.2015.7161142

G. Ai, Y. Zhenyu, L. Suo and X. Wenjun, Research of Function Safety of the Hardware Platform of CNC System, 2017 10th International Conference on Intelligent Computation Technology and Automation (ICICTA), Changsha, 2017, pp. 207-210.

http://dx.doi.org/10.1109/icicta.2017.53

Refbacks

There are currently no refbacks.

Username
Password
Remember me