Development of Laminated Rubber-Metal Spring using Standard Malaysia Rubber Constant Viscosity-60

Mohd Azli Salim(1*), A. Putra(2), M. A. Abdullah(3), N. Ahmad(4)

(1) Green Technology Vehicle, Centre for Advanced Research on Energy, Faculty of Mechanical Engineering, UniversitiTeknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
(2) Sustainable Maintenance Engineering, Centre for Advanced Research on Energy, Faculty of Mechanical Engineering, UniversitiTeknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
(3) Advanced Vehicle Technology, Centre for Advanced Research on Energy, Faculty of Mechanical Engineering, UniversitiTeknikal Malaysia Melaka, Hang Tuah Jaya, 76100 Durian Tunggal, Melaka, Malaysia
(4) Engineering & Product Design Unit, Technology & Engineering Division, LembagaGetah Malaysia, 47000 Sungai Buloh, Selangor, Malaysia
(*) Corresponding author


DOI's assignment:
the author of the article can submit here a request for assignment of a DOI number to this resource!
Cost of the service: euros 10,00 (for a DOI)

Abstract


Laminated rubber-metal spring is a new challenging research because previously, it is known as s rubber bearing and its application confined to the field of civil engineering. With the creation of this research, they may applied to mechanical engineering because it was believed could reduce the level of vibration in the car engine system. This paper presents the development of laminated rubber-metal spring which is the key ingredient is standard Malaysia rubber constant viscosity - 60. There are several steps involved to develop the product by different number of degree of freedom and it is discussed in details. Many standard are adopted from open literature and it need to be followed every single step to make this product more reliable and trustworthy data for presentation and future analysis. Overall, the discussion of developing this product is come out together with several figure to present it well.
Copyright © 2014 Praise Worthy Prize - All rights reserved.

Keywords


Laminated Rubber-Metal Spring; Standard Malaysia Rubber Constant Viscosity – 60

Full Text:

PDF


References


Shi, Y., Wu, P.D., Lloyd, D.J., Li, D.Y., Effect of rate sensitivity on necking behavior of a laminated tube under dynamic loading, Journal of Applied Mechanics, Transactions ASME, Vol. 81, No. 5, 2014, art no. 051010.

Pan, G.Y., Yang, X., Yan, Y., Optimization of vehicle powertrain mounting system and its performance, Applied Mechanics and Materials, 2014, pp. 580-583.

Xie, Z., Yu, D., Li, R., Multi-objective robust optimization design of vehicle engine mount systems, QicheGongcheng/Automotive Engineering, Vol. 35, No. 10, 2013, pp. 893-897.

Lindley, Engineering design with natural rubber, The Malaysian Rubber Producers’ Research Association, 1984.

Mohd Noor ArbRejab, Roslan Abdul Rahman, Raja Ishak Raja Hamzah, Jawaid Iqbal InayatHussain, NazirahAhamd, Asyraf Ismail, Azma Putra, Fabrication process and mechanical properties of elastomeric mount, The 7th South East Asia Technical University Consortium (SEATUC) Symposium, 2013, 97.

The Malaysian Rubber Producers’ Research Association, Engineering design with natural rubber, NR Technical Bulletin, 1992, ISSN 0956-3856.

Jayakumar, L., Balamurugan, K., Ezilarasan, C., Wear and friction behaviour of 7075Al-25 SiC particle composites sliding against automobile friction material, (2014) International Review of Mechanical Engineering (IREME), 8 (1), pp. 190-196.

Rus, A.Z.M., Siti Rahmah, M., Rus, S.M., Influence of N2 and H2O on UV irradiated bio polymer composite, (2014) International Review of Mechanical Engineering (IREME), 8 (1), pp. 271-276.


Refbacks

  • There are currently no refbacks.



Please send any question about this web site to info@praiseworthyprize.com
Copyright © 2005-2021 Praise Worthy Prize