Investigate the Effect of Using Sunflower Oil as a Lubricant During Turning Operation of Stainless Steel
(*) Corresponding author
DOI's assignment:
the author of the article can submit here a request for assignment of a DOI number to this resource!
Cost of the service: euros 10,00 (for a DOI)
Abstract
The study was focused on the effect of using Sunflower Oil as a lubricant during turning operation of Stainless Steel. Cutting speed, feed rate and depth of cut were set as the control factor for the machining operation. An Orthogonal Array of L4 (2³) was used. Then ANOVA analyses were carried out to identify the significant factors affecting surface roughness, Ra and tool wear, Vb, and determined the optimal cutting combination design by seeking the responses and signal-to-noise ratio. Finally, the confirmations run can optimize the optimal parameters and cutting fluid for surface roughness and tool wear
Copyright © 2014 Praise Worthy Prize - All rights reserved.
Keywords
Full Text:
PDFReferences
S. Thamizhmanii, S. Hasan, “Analyses of surface roughnessby turning process using taguchi method”, Journal of achievement in Materials and Manufacturing Engineering, 20, 2007.
M. Soković, K. Mijanović, “Ecological aspects of cutting fluids and its influence on quantifiable parameters of the cutting processes,” Journal of Materials Processing Technology 2001;109:181-189.
J. John, M. Bhattacharya, P. C. Raynor, “Emulsions containing vegetable oils for cutting fluid application,” Colloids and Surfaces A: Physicochem. Eng. Aspects 2004;237:141-150.
W. Belluco, L. De Chiffre, “Testing of vegetable-based cutting fluids by hole making operations,” Lubrication Engineering 2001;57:12-16.
S. A. Adam, N. A. Shuaib, M. R. M. Hafiezal, S. N. Suhaili, “Study on Surface Roughness and Chip Formation using Milling Operation of Mild Steel Using Vegetable Based Oil as a Lubricant”, International Journal of Engineering & Technology IJET-IJENS, 2013:Vol:13 No:01, pp.19-23.
N.J. Fox, B. Tyrer, and G.W. Stachowiak, “Boundary lubrication performance of free fatty acids in sunflower oil”, Tribology Letters, Vol. 16, No. 4, May 2004.
Sokovic, M. and Mijanovic, K., “Ecological aspects of the cutting fluids and its influence on quantifiable parameters of cutting processes”, Journal of Materials Processing Technology, 109(1-2):181-189, 2001.
Belluco, W., and Chiffre, L. D., “Performance evaluation of vegetable-based oils in drilling austenitic stainless steel”, Journal of Materials Processing Technology 2004: 148:171–176.
Safian, S., Hisyam, M.A. and Aman, S., Evaluation of Vegetable Oil as an Alternative Cutting Lubricant When End Milling Martensutic Stainless Steel Using Uncoated Carbide Tool, Journal of Advanced Manufacturing and Technology, ISSN: 1985-3157 Vol. 3 No. 2, pp.49-55, 2009.
Zailani, Z.A., Sanuddin, A.B., Hussin, M.S., Khalil, A.N.M., Hamzas, M.F.M.A., Ahmad Mustafa, N., An effect of boric acid mixture as solid lubricant towards machining processes, (2013) International Review of Mechanical Engineering (IREME), 7 (5), pp. 912-918.
Hussin, M.S., Zailani, Z.A., Hadi, H., Sanuddin, A.B., Hamzas, M.F.M.A., A study on the effect of boric acid mixture as solid lubricant towards machining processes, (2012) International Review of Mechanical Engineering (IREME), 6 (7), pp. 1429-1433.
Refbacks
- There are currently no refbacks.
Please send any question about this web site to info@praiseworthyprize.com
Copyright © 2005-2024 Praise Worthy Prize