Email this article 
A Novel Approach for Parameters Determination in Four Lumped PV Parametric Model with Operative Range Evaluations
(*) Corresponding author
DOI's assignment:
the author of the article can submit here a request for assignment of a DOI number to this resource!
Cost of the service: euros 10,00 (for a DOI)
Abstract
The paper presents a novel numerical approach for the parameters determination of crystalline silicon PV models four lumped parameters equivalent circuit. The novel approach basically deals with a new method, alternative to the iterative one known in literature, to calculate the series resistance. Particularly, it allows the evaluation of the lumped parameters on the basis of the manufacturer’s datasheet. The new approach has been validated both in the Maximum Power Point (MPP) and close to it by comparing values and curves obtained by means of the model implementation in Matlab/Simulink environment with those related to some five parameters models and manufacturer curves. Results show that when temperature and radiation are at their STC (Standard Technical Condition) values, the four lumped parameters model here developed shapes the manufacturer I-V characteristics curves better than the other models. Moreover, what above has been investigated to be true even if radiation is lower than 1000 W/m2 but not when temperature is higher than 298.15 K. Finally, the four lumped parameters model here developed is to be preferred to the five lumped parameters ones if temperature value is lower than 323.15 K
Copyright © 2013 Praise Worthy Prize - All rights reserved.
Keywords
References
Brando, G., Dannier, A., del Pizzo, A., Rizzo, R., Power Electronic Transformer for advanced grid management in presence of distributed generation, (2011) International Review of Electrical Engineering (IREE), 6 (7), pp. 3009-3015.
G. Brando, A. Dannier, A. Del Pizzo, and R. Rizzo, “A high performance control technique of power electronic transformers in medium voltage grid-connected PV plants,” in 19th International Conference on Electrical Machines, ICEM 2010, 2010.
R. Rizzo, P. Tricoli, and I. Spina, “An innovative reconfigurable integrated converter topology suitable for distributed generation,” Energies, vol. 5, pp. 3640–3654, 2012.
A. Andreotti, A. Del Pizzo, R. Rizzo, and P. Tricoli, “An efficient architecture of a PV plant for ancillary service supplying,” in SPEEDAM 2010 - International Symposium on Power Electronics, Electrical Drives, Automation and Motion, 2010, pp. 678–682.
V. Di Dio, R. Miceli, C. Rando, and G. Zizzo, “Dynamics photovoltaic generators: Technical aspects and economical valuation,” in Power Electronics Electrical Drives Automation and Motion (SPEEDAM), 2010 International Symposium on, 2010, pp. 635–640.
A. Luque and S. Egedus, Handbook of Photovoltaic Science and Engineering. 2003.
M. Wolf and H. Raushenbach, “Series resistance effects on solar cell measurements,” in Pacific General Meeting of the AIEE, 1961.
T. U. Townsend, “A method for estimating the long-term performance of direct coupled photovoltaic systems,” University of Wisconsis, Madison, 1989.
M. Bouzguenda, T. Salmi, A. Gastli, and A. Masmoudi, “Evaluating solar photovoltaic system performance using MATLAB,” in Renewable Energies and Vehicular Technology (REVET), 2012 First International Conference on, 2012, pp. 55–59.
G. Farivar and B. Asaei, “Photovoltaic module single diode model parameters extraction based on manufacturer datasheet parameters,” in Power and Energy (PECon), 2010 IEEE International Conference on, 2010, pp. 929–934.
V. Lo Brano, A. Orioli, and G. Ciulla, “On the experimental validation of an improved five-parameter model for silicon photovoltaic modules,” Solar Energy Materials and Solar Cells, vol. 105, pp. 27–39, 2012.
E. Matagne, R. Chenni, and R. El Bachtiri, “A photovoltaic cell model based on nominal data only,” in Power Engineering, Energy and Electrical Drives, 2007. POWERENG 2007. International Conference on, 2007, pp. 562–565.
V. Di Dio, D. La Cascia, R. Miceli, and C. Rando, “A mathematical model to determine the electrical energy production in photovoltaic fields under mismatch effect,” in Clean Electrical Power, 2009 International Conference on, 2009, pp. 46–51.
D. Sera, R. Teodorescu, and P. Rodriguez, “PV panel model based on datasheet values,” in Industrial Electronics, 2007. ISIE 2007. IEEE International Symposium on, 2007.
R. C. Campbell, “A Circuit-based Photovoltaic Array Model for Power System Studies,” in Power Symposium, 2007. NAPS ’07. 39th North American, 2007, pp. 97–101.
V. Lo Brano, A. Orioli, G. Ciulla, and A. Di Gangi, “An improved five-parameter model for photovoltaic modules,” Solar Energy Materials and Solar Cells, vol. 94, pp. 1358–1370, 2010.
M. G. Villalva, J. R. Gazoli, and E. R. Filho, “Comprehensive Approach to Modeling and Simulation of Photovoltaic Arrays,” Power Electronics, IEEE Transactions on, vol. 24, pp. 1198–1208, May 2009.
A. N. Celik and N. Acikgoz, “Modelling and experimental verification of the operating current of mono-crystalline photovoltaic modules using four- and five-parameter models,” Applied Energy, vol. 84, pp. 1–15, 2007.
K. Ishaque, Z. Salam, and H. Taheri, “Simple, fast and accurate two-diode model for photovoltaic modules,” Solar Energy Materials and Solar Cells, vol. 95, pp. 586–594, 2011.
R. Chenni, M. Makhlouf, T. Kerbache, and A. Bouzid, “A detailed modeling method for photovoltaic cells,” Energy, vol. 32, pp. 1724–1730, 2007.
M. A. de Blas, J. L. Torres, E. Prieto, and A. Garcia, “Selecting a suitable model for characterizing photovoltaic devices,” Renewable Energy, vol. 25, pp. 371–380, 2002.
C. Carrero, J. Rodriguez, D. Ramirez, and C. Platero, “Simple estimation of PV modules loss resistances for low error modelling,” Renewable Energy, vol. 35, pp. 1103–1108, 2010.
Huan-Liang Tsai, C.-S. Tu., and Y.-J. Su, “Development of Generalized Photovoltaic Model Using MATLAB/SIMULINK,” in Engineering and Computer Science. WCECS 2008. World Congress on , 2008.
W. De Soto, S. A. Klein, and W. A. Beckman, “Improvement and validation of a model for photovoltaic array performance,” Solar Energy, vol. 80, pp. 78–88, 2006.
R. Candela, V. Di Dio, E. Riva Sanseverino, and P. Romano, “Reconfiguration Techniques of Partial Shaded PV Systems for the Maximization of Electrical Energy Production,” in Clean Electrical Power, 2007. ICCEP ’07. International Conference on, 2007, pp. 716–719.
P. Roopa, S. E. Rajan, and R. P. Vengatesh, “Performance analysis of PV module connected in various configurations under uniform and non-uniform solar radiation conditions,” in Recent Advancements in Electrical, Electronics and Control Engineering (ICONRAEeCE), 2011 International Conference on, 2011, pp. 142–149.
T. Salmi, M. Bouzguenda, A. Gastli, and A. Masmoudi, “MATLAB/Simulink Based Modeling of Photovoltaic Cell,” International Journal of Renewable Energy Research (IJRER), vol. 2, pp. 213–218, 2012.
F. Genduso and R. Miceli, “A general mathematical model for non-redundant fault-tolerant inverters,” in Electric Machines Drives Conference (IEMDC), 2011 IEEE International, 2011, pp. 705–710.
V. Di Dio, S. Favuzza, D. La Cascia, and R. Miceli, “Economical Incentives and Systems of Certification for the Production of Electrical Energy from Renewable Energy Resources,” in Clean Electrical Power, 2007. ICCEP ’07. International Conference on, 2007, pp. 277–282.
A. O. Di Tommaso, F. Genduso, and R. Miceli, “Analytical Investigation and Control System Set-up of Medium Scale PV Plants for Power Flow Management,” Energies, vol. 5, pp. 4399–4416, 2012.
Refbacks
- There are currently no refbacks.
Please send any question about this web site to info@praiseworthyprize.com
Copyright © 2005-2024 Praise Worthy Prize
