Open Access Open Access  Restricted Access Subscription or Fee Access

Accurate Analysis of Effective Parameters on Design of Furnace Using Voltage Source Inverter


(*) Corresponding author


Authors' affiliations


DOI: https://doi.org/10.15866/irecon.v5i5.14524

Abstract


In this paper, model of induction heater coil is presented and it is shown how to design a proper coil for induction melting. Also, effective parameters on coil design are indicated and it is shown how to consider them to improve coil design. Moreover, effects of these parameters are compared with each other. In the final section model of induction heater with voltage source inverter is presented and effective parameters on total efficiency of transmitting power to the load are investigated and experimental and theoretical results are compared in order to verify theory and equations indicated in the paper.
Copyright © 2017 Praise Worthy Prize - All rights reserved.

Keywords


Induction Heater; Coil Design; Melting Rate; Melting Time; Efficiency; Voltage Source Inverter; Pulse Frequency Modulation

Full Text:

PDF


References


J. Davies, P.Simpson, Induction heating handbook, (McGRAW-HILL 1979).

J. Lee, S. Lim, K. Nam, D. Choi, An Optimal Selection of Induction-Heater Capacitance Considering Dissipation Loss Caused by ESR, IEEE Trans on Ind. Appl, Vol. 43, No. 4, July/August 2007.

F. P. Dawson, P. K. Jain, A Comparison of Load Commutated Inverter Systems for Induction Heating and Melting Applications, IEEE Trans. on Power Electronics. Vol. 6. No. 3. July 1991.

P.Dorland, J.D. Wyk, O. H. Stielau, On the Influence of Coil Design and Electromagnetic Configuration on the Efficiency of an Induction Melting Furnace, IEEE Trans. Ind. Appl, vol. 36, no. 4, July/August 2000.

J. Davies, Conduction and Induction Heating Theory, (IEE Press2000).

F. W. Curtis, High frequency Induction Heating, (McGRAW-HILL 1950).

V. Rudnev, D. Loveless, R. Cook, M. Bloack, Handbook of Induction Heating, (Marcel Dekker 2003).

J. T. S. Trydom, J. D. V. Wyc, J. A. Ferreira, Capacitor Measurements for Power Electronic Applications, Thirty-Fourth IAS Annual Meeting, IEEE. Volume 4, Page(s):2435 - 2440 1999.

Y. D. Choi, D. Y. Lee, D. S. Hyum, A Study on the New Control Scheme of Class-E Inverter for IH-Jar Application with Clamped Voltage Characteristics Using Pulse Frequency Modulation, Industry Applications Conference, IEEE Vol. 2, On page(s): 1346- 1351, 2002.

S. Nagai, A. Okuno, High-Frequency Inverter with Phase-Shifted PWM and Load-Adaptive PFM Control Strategy for Industrial Induction-Heating, Industry Applications Society Annual Meeting, 1993, IEEE, Oct. 1993 Page(s):2165 - 2172.

H. Fujita, Pulse-Density-Modulated Power Control of a 4 kW, 450 kHz Voltage-Source Inverter for Induction Melting Applications, IEEE Transactions on Industry Applications, Vol 32, Nn 2, 1996.

A. Sandali, A. Cheriti, P.Sicard, Comparison of the Various PDM Control Modes, IEEE International Conference on Industrial Technology (ICIT), 2004.

H. Ogiwara, M. Ltoi, M. Nakaoka, PWM-Controlled Soft-Switching SEPP High-Frequency Inverter for Induction Heating Applications, IEE Proc.- Electr. Power Appl., Vol. 151, No. 4, July 2004.

S. Nagai, A. Okuno, High-Frequency Inverter with Phase-Shifted PWM and Load-Adaptive PFM Control Strategy for Industrial Induction-Heating, Industry Applications Society Annual Meeting,IEEE, Oct. 1993 Page(s):2165 – 2172, 1993.

R. W. Brown, Modeling of Capacitor Parameters Related to the Metal Film Layer With Partial Edge Disconnection, IEEE Transaction On Component and Packaging Technologies, Vol. 30, No. 4, December 2007.


Refbacks

  • There are currently no refbacks.



Please send any question about this web site to info@praiseworthyprize.com
Copyright © 2005-2024 Praise Worthy Prize